A.K Enterprises

Transmitter Remote control:

• Modulation mode: ASK (Amplitude Modulation).
• Encoder types: fixed code.
• Decoding receiver board:
• Receiver Operating voltage: DC 5V.
• Receiver sensitivity is: -98dB.
• Leg 7 bits: VT, D3, D2, D1, D0, +5V and GND.
• VT is a valid signal high output pin upon receiving a valid signal, the pin output high may also drive the relay.
• Size: 7 x 22 x 41 mm.

• Single channel RF (radio frequency) wireless remote input 12V DC
• Output single channel controlled by RF remote A-B-C( N/O - COM - N/C)
• N/O (normally open) COM (common) these two are used as a switch for loads max: 10 A
• No direction required for remote as like IR remote

• Operating Voltage: DC12V
• Transmitting Frequency: 315MHz
• Transmission Distance: 80M (Open field)
• Firing Range: 100meter
• High Quality Genuine Products
• Shock Resistance: 4.7m
• Receiver Board: Operating
• Operating Frequency: 315MHz
• Voltage: DC12V
• Encoding Type: Learning Code Max

Model: TX118SA-4

• Transmitting power: 11dbm
• Distance: 30-100m
• Emission current: 10MA
• Rate of fire: maximum 10KB / S
• Transmit deviation: +/- 7. 5KHZ / narrow-band emission
• Modulation: ASK
• Operating Voltage: DC 3V-24v
• Encoding : EV1527 1527 Learning code
• Each module has a unique ID address code.
• All modules K1-K4 four key code is the same.

Pin Description:

• - : Negative power supply
• +: Positive power supply, DC 3-24V
• Pin Description:
• - : Negative power supply
• +: Positive power supply, DC 3-24V
• K1: 1 short to  Negative start transmitting data, Similar the A button on the remote control.
• K2:  2 short to  Negative start transmitting data, Similar the B  button on the remote control.
• K3:  3 short to  Negative start transmitting data, Similar the C  button on the remote control.
• K4:  4 short to  Negative start transmitting data, Similar the D  button on the remote control.
• ANT: transmitting antenna

• Voltage - DC 12V
• Power - 10A Relay
• Durable and Long lasting
• DC 12v 2 CH Channel Wireless RF Remote Control Switch Transmitter Receiver 10A Relay

1. Operating voltage: DC 5V
2. Operating temperature: -40~80 degrees
3. Operating frequency: 433MHZ Receive sensitivity: ≥-95dB
4. Working Mode: jump switch, point action, self-locking, and interlocking(adjustable
5. Operation Manual: Press the learn button for 2 or 3 seconds, lights out (that has entered the state of learning), Release the learning button, press any key of the remote control, and the indicator light flashes 5 times to show the success of the study. Note: The controller can learn the fixed code/learning code, a total of 16 different encodings, arbitrary button remote control, and beyond will be cleared in the early learning of remote control.
6. Removal method: Continue to hold down the learning button for about 8 seconds. The indicator light is extended from extinction to success.

1. Input range: 12 to 75V DC
2. Output range: 12 to 75V DC
3. Material: PVC Plastic
4. Remote Frequency: 433 MHz
5. Simple Plug and Play Operation

6. This is a wireless remote control switch for a universal relay receiver module. Control DC devices through remote simple plug-and-play connections with the long-range inbuilt receiver at module side and two key remote transmitters.

   This relay module operates at the Input range of 12 to 75 VDC and similarly, at the output, it can operate the device at the range of 12 to 75 VDC.

   About Working mode:Momentary: Push the remote button, the relay connects, release the remote button, the relay disconnects.Toggle: Push once the remote button, the relay connects, push twice the remote button, the relay disconnects.Latching: Push the remote button A, the relay connects, push the remote button B, the relay dis-connect.Clearing the code:Method 1: Push the learning button on the receivers for 8 times, the codes will be cleaned;Method 2: Keeping press the Learning Button on the receiver until the LED indicator is ON and then flashes until it flashes 8 times.it means the code has been cleared successfully; After clearing the code, all the remote control cannot work anymore.Learning the code : (Momentary) Push the learning key on the receiver 1 time, it comes into momentary setting mode. Wait for a moment, the LED will be off, it comes into a learning state. Push the remote button, the LED indicator on the receiver board will flash then come off. After 3 seconds, the LED indicator will be on again, learning successfully.Learning the code : ( Toggle ) Push the learning key on the receiver 2 times, it comes into toggle setting mode Wait for a moment, the LED will be off, it comes into a learning state. Push the remote button, the LED indicator on the receiver board will flash then come off. After 3 seconds, the LED indicator will be on again, learning successfully.Learning the code 🙁 Latching ) Note: When you choose latching mode, in order to learn more remote control, you need to learn two different buttons, the first time learned is for “ON”, the second time learned for “OFF”. For example button A = ON, button B = OFF Push the learning key on the receiver 3 times, it comes into latching mode. Wait for a moment, the LED indicator on the receiver board will flash then come off. Push the remote button A . LED flash 5 times. Push the remote button B. Led flash for 5 times. After 3 seconds, the LED indicator will be on again, learning successfully. A = ON , B = OFF .

• Input Power:DC10V-14V
• Standby Current:<5MA
• RF Frequency:315M or 433M
• Receive sensitivity: >97dbm
• Decoding mode:MCU software decoding

Wireless relay module using remote control to switch a relay using a remote. It can be used as a 1 channel wireless switch.

Applications: Garage Door, Household Electrical Appliances, RGB lights

Stable performance and strong to resist interference, not obstructed by walls and furniture!
Reference distance: 150 meters (This is the theory distance in open environment without interference, practical application due to the interference environment and decreased)

Characteristic: Double control(wall switch function and control function),safety(the shell applies to the fire-retardant material),easy installation(just wire connection)

This hybrid RF Transceiver Module provides a complete RF transmitter and receiver module solution which can be used to transmit data at up to 3KHz from any standard CMOS/TTL source.

The transmitter module is very simple to operate and offers low current consumption (typical. 11mA). Data can be supplied directly from a microprocessor or encoding device, thus keeping the component count down and ensuring a low hardware cost.

The RX – ASK is an ASK Hybrid receiver module. The RF Transmitter Receiver Module is an effective low-cost solution for using 433 MHz. The TX-ASK is an ASK hybrid transmitter module. TX-ASK is designed by the saw resonator, with an effective low cost, small size and simple to use for designing.

Specifications of 433MHz RF Transmitter Receiver Wireless Module:-

• Range in open space(Standard Conditions) : 100 Meters
• RX Receiver Frequency : 433 MHz
• RX Typical Sensitivity : 105 Dbm
• RX Supply Current : 3.5 mA
• RX IF Frequency : 1MHz
• RX Operating Voltage : 5V
• TX Frequency Range : 433.92 MHz
• TX Supply Voltage : 3V ~ 6V
• TX Out Put Power : 4 ~ 12 Dbm

Features of 433MHz RF Transmitter Receiver Wireless Module:-

• Low Power Consumption
• Easy For RF based Application
• Complete Radio Transmitter
• Transmit Range Up To 50m
• CMOS / TTL Input
• No Adjustable Components
• Very Stable Operating Frequency
• Low Current Consumption (Typ 11mA)
• Wide Operating Voltage
• ASK Modulation